jwsporty
11-12-03, 05:25 AM
The Colubrid Rack
Well I decided to post my latest rack system with the hope that this will help out others looking for a way to efficiently store smaller snakes. I can not lay claim to the design as the inspiration has come from Marcus Jayne Ball Pythons.
http://www.ballpythons.ca
Having seen this rack in action, I decided I needed a scaled down version for my kings and corns. Easy to build, well priced and very effective.
http://www.ssnakess.com/photopost/data/500/1149room1-racks.jpg
So here it is
Materials required:
5/8 Melamine
Cuts:
2 41x13 (sides)
1 24x13 (base)
2 18 x 3 (spacers)
7 18 x 24 (shelves)
1/8 Hardboard
Cuts:
1 41 x 19-1/8
Note: Make it easy on yourself and have the renovation center cut the wood for you. Its cheap. I had mine done at Home depot.
Other Materials:
3 11 Heat tape
1 two prong extension cord - 6+ (cut off the female plug)
digitial dual probe thermometer
slide thermostat
6 Sterilite Model # 1856 container Available at Walmart
Other construction materials
solder for making connections between extension cord and heat tape or heat tape connectors
tube of silicone (clear or white) I used clear.
box of 100 - 1-1/2 x #8 Particleboard screws
screw head covers
melamine iron-on edge stripping (13/16x50)
small package 1 nails
duct tape
2 small brackets
Tools:
Electric drill
Drill bit to pre-drill all holes
Bit to set screws, or screw driver, appropriate screw head pattern (I used the #2 robertson)
Ruler (12 is fine)
Marker
Clothes Iron
Hammer
Sharp Knife
Soldering Iron
Starting assembly
Building the base and edging
Start by placing the piece 13x24 on a flat surface and position the two spacers, one in front and one in back , equally spaced side by side. Mark for center. Apply a bead of silicone along the mating edge of the spacers, re-align your marks and attach the spacers as shown in pic . I used 5 screws drilled up from the bottom.
http://www.ssnakess.com/photopost/data/500/1149rack-build1.jpg
Note: Use Particleboard screws only and PRE-DRILL everything before using the screws. If you do this you will not have splitting.
Also: Apply a bead of silicone on all jointing surfaces. This will make for a stronger unit and avoid potential problems is you are ever infected with mites and need to thoroughly clean the unit.
Next, position the sides and attach to the ends of the spacers using two screws per contact point, make sure to apply a bead on silicone.
At this point you will want to edge trim the base and sides, edging only has to be applied to the visible side, (so the front and sides of the base, and the front edge of the vertical sides), It is easier to do this at this stage instead of leaving it until the end. I ran out of edging for this phootshoot so I did not get a chance to do this myself.
http://www.ssnakess.com/photopost/data/500/1149rack-build2.jpg
Next, drop the first shelf into place, align for a flush mount at the back, make sure it is seated properly on top of the spacers. Re-install using silicone. Find the vertical center of the first shelf and mark three spots where the screws will be installed, I used the markings of 1, 6.5 and 12. Pre-drill the holes and set screws for both sides.
http://www.ssnakess.com/photopost/data/500/1149rack-build3.jpg
Next take the first sterilite container and place it on the shelf. I took 4 pieces of paper and placed them under the four corners of the tub as vertical spacers. This will make the containers slide easier once construction is completed. DON'T try to put all the tubs, spacers and shelves in first and then screw into place. This will cause binding of the shelves.
Place the next shelf on top of the container and again position for flush mount at the back and for proper seating. Pre-drill, silicone and set screws as you go along. Finish off by laying a bead of silicone in the corners before you put the next container in place. Work clean
Continue these steps until all the shelves are installed.
http://www.ssnakess.com/photopost/data/500/1149rack-build4.jpg
It is that simple.
http://www.ssnakess.com/photopost/data/500/1149rack-build5.jpg
Once all the shelves are in place, give a light coat of silicone to all raw edges at the back of the unit, again to avoid the potential of giving mites a place to lay their eggs. Allow this to dry thoroughly.
http://www.ssnakess.com/photopost/data/500/1149rack-build6.jpg
Heating
Next you have to prepare your heat tape. I used the solder method. Note, heat tape is not CSA approved so pay close attention to your work and make sure the connections are secure. If you dont feel comfortable doing this work, please have someone do it for you. Safety first !! I finished the connection process by applying a little dab of silicone over the soldered area, allowed it to dry and then wrapped in duct tape to protect the connection point.
http://www.ssnakess.com/photopost/data/500/1149rack-build7.jpg
http://www.ssnakess.com/photopost/data/500/1149rack-build8.jpg
Also see Jeff's article on Heat tape for further details.
http://www.ssnakess.com/forums/showthread.php?s=&threadid=5896
Plug in the heat tape and test your work to make sure it is working properly.
Next , position the heat tape across the back of the unit, vertically. Temporarily secure the heat tape at the top using a couple of strips of duct tape if you dont have an extra set of hands to help. Nail the heat tape in place, making sure that you do not puncture the copper strip or black portions of the tape and nail on every shelf. For added security I laid down a couple of strips of duct tape and a couple of small brackets to hold the wires in place.
http://www.ssnakess.com/photopost/data/500/1149rack-build9.jpg
Note: in this picture, the retainer clip has not yet been installed
Finishing
Next, hold in position and mount the 1/8 hardboard for the backing, again pay attention that you dont puncture the heat tape.
http://www.ssnakess.com/photopost/data/500/1149rack-build10.jpg
At this stage, you can finish all edge trimming and install all the screw head covers
Next drill a small hole through the hard board to allow passage of the probe for the thermometer. I placed my probe directly on the heat tape and secured with a piece of duct tape on the third shelf. If you wish, secure the mounting plate for the thermometer in a place of your choosing.
Next, silicone the slide thermostat onto the unit, again at a place of your choice.
Allow everything to dry thoroughly before use.
Plug it in and test it.
I also checked all nail heads holding the back in place to make sure that I had not punctured the heat tape. If you did you will get a shock. Remove the nail if this problem is discovered. I did end up with one that needed to be removed.
Well thats it. Put it into position, plug it in, set the temps and you are ready to go.
I let mine sit for a day, so that the temps could stabilize and then I prepped the containers. Drill air holes in the locations of your choice in the containers and make sure the holes arent too big for the snake to escape. Clean them and set them up with nothing more then a good bed of aspen and a water dish.
You do not need to put in hides if the snake is older, but for juveniles you can keep it simple and throw in a few toilet paper tubes and plastic containers for their added security.
This design allows for a very good heat and light gradient. Its easy to clean, easy to move around, takes up little space and is very strong.
Currently I am using this setup for juvenile corns, mid size kings, a juvenile boa, and 4 male ball python.
Here is a summary of costs:
All prices in Canadian Funds
5/8 Melamine 23.00
1/8 Hardboard 12.00
3 11 Heat tape 15.00
1 two prong extension cord - 6+ (cut off the female plug) 8.00
digitial dual probe thermometer 22.00
slide thermostat 20.00
6 Sterilite Model # 1856 container Available at Walmart 5.43 ea 32.58
solder for making connections between extension cord and heat tape or heat tape connectors
tube of silicone (clear or white) I used clear. 6.00
box of 100 - 1-1/2 Particleboard screws 5.00
screw head covers 3.00
melamine iron-on edge stripping (13/16x50) 8.00
small package 1 nails 1.00
duct tape 4.00
2 small brackets 1.00
Plus about 4 hours labour to assemble
Total: 160.00 or approx. 26.66 per snake housing
You will save more if you cut enough wood for two units
Plus tax of course. Your heat tape may be more, I did get a deal on mine through a private sale
UPDATE:
Initially, the recommendation was to mount the thermometer probe directly to the heat tape. Although this gives you an accurate reading at the source, it does not properly measure the temp inside the tubs. Since then, I have installed the probe inside the tub and put a sheet of double sided aluminum foil insulation across the back of the unit. Using the foil insulation greatly improves the efficiency in getting the heat back into the tub, where it is needed.
Well I hope this helps someone out, and if you have any further questions, drop me a line. Ill be happy to help.
Cheers
Jim
Well I decided to post my latest rack system with the hope that this will help out others looking for a way to efficiently store smaller snakes. I can not lay claim to the design as the inspiration has come from Marcus Jayne Ball Pythons.
http://www.ballpythons.ca
Having seen this rack in action, I decided I needed a scaled down version for my kings and corns. Easy to build, well priced and very effective.
http://www.ssnakess.com/photopost/data/500/1149room1-racks.jpg
So here it is
Materials required:
5/8 Melamine
Cuts:
2 41x13 (sides)
1 24x13 (base)
2 18 x 3 (spacers)
7 18 x 24 (shelves)
1/8 Hardboard
Cuts:
1 41 x 19-1/8
Note: Make it easy on yourself and have the renovation center cut the wood for you. Its cheap. I had mine done at Home depot.
Other Materials:
3 11 Heat tape
1 two prong extension cord - 6+ (cut off the female plug)
digitial dual probe thermometer
slide thermostat
6 Sterilite Model # 1856 container Available at Walmart
Other construction materials
solder for making connections between extension cord and heat tape or heat tape connectors
tube of silicone (clear or white) I used clear.
box of 100 - 1-1/2 x #8 Particleboard screws
screw head covers
melamine iron-on edge stripping (13/16x50)
small package 1 nails
duct tape
2 small brackets
Tools:
Electric drill
Drill bit to pre-drill all holes
Bit to set screws, or screw driver, appropriate screw head pattern (I used the #2 robertson)
Ruler (12 is fine)
Marker
Clothes Iron
Hammer
Sharp Knife
Soldering Iron
Starting assembly
Building the base and edging
Start by placing the piece 13x24 on a flat surface and position the two spacers, one in front and one in back , equally spaced side by side. Mark for center. Apply a bead of silicone along the mating edge of the spacers, re-align your marks and attach the spacers as shown in pic . I used 5 screws drilled up from the bottom.
http://www.ssnakess.com/photopost/data/500/1149rack-build1.jpg
Note: Use Particleboard screws only and PRE-DRILL everything before using the screws. If you do this you will not have splitting.
Also: Apply a bead of silicone on all jointing surfaces. This will make for a stronger unit and avoid potential problems is you are ever infected with mites and need to thoroughly clean the unit.
Next, position the sides and attach to the ends of the spacers using two screws per contact point, make sure to apply a bead on silicone.
At this point you will want to edge trim the base and sides, edging only has to be applied to the visible side, (so the front and sides of the base, and the front edge of the vertical sides), It is easier to do this at this stage instead of leaving it until the end. I ran out of edging for this phootshoot so I did not get a chance to do this myself.
http://www.ssnakess.com/photopost/data/500/1149rack-build2.jpg
Next, drop the first shelf into place, align for a flush mount at the back, make sure it is seated properly on top of the spacers. Re-install using silicone. Find the vertical center of the first shelf and mark three spots where the screws will be installed, I used the markings of 1, 6.5 and 12. Pre-drill the holes and set screws for both sides.
http://www.ssnakess.com/photopost/data/500/1149rack-build3.jpg
Next take the first sterilite container and place it on the shelf. I took 4 pieces of paper and placed them under the four corners of the tub as vertical spacers. This will make the containers slide easier once construction is completed. DON'T try to put all the tubs, spacers and shelves in first and then screw into place. This will cause binding of the shelves.
Place the next shelf on top of the container and again position for flush mount at the back and for proper seating. Pre-drill, silicone and set screws as you go along. Finish off by laying a bead of silicone in the corners before you put the next container in place. Work clean
Continue these steps until all the shelves are installed.
http://www.ssnakess.com/photopost/data/500/1149rack-build4.jpg
It is that simple.
http://www.ssnakess.com/photopost/data/500/1149rack-build5.jpg
Once all the shelves are in place, give a light coat of silicone to all raw edges at the back of the unit, again to avoid the potential of giving mites a place to lay their eggs. Allow this to dry thoroughly.
http://www.ssnakess.com/photopost/data/500/1149rack-build6.jpg
Heating
Next you have to prepare your heat tape. I used the solder method. Note, heat tape is not CSA approved so pay close attention to your work and make sure the connections are secure. If you dont feel comfortable doing this work, please have someone do it for you. Safety first !! I finished the connection process by applying a little dab of silicone over the soldered area, allowed it to dry and then wrapped in duct tape to protect the connection point.
http://www.ssnakess.com/photopost/data/500/1149rack-build7.jpg
http://www.ssnakess.com/photopost/data/500/1149rack-build8.jpg
Also see Jeff's article on Heat tape for further details.
http://www.ssnakess.com/forums/showthread.php?s=&threadid=5896
Plug in the heat tape and test your work to make sure it is working properly.
Next , position the heat tape across the back of the unit, vertically. Temporarily secure the heat tape at the top using a couple of strips of duct tape if you dont have an extra set of hands to help. Nail the heat tape in place, making sure that you do not puncture the copper strip or black portions of the tape and nail on every shelf. For added security I laid down a couple of strips of duct tape and a couple of small brackets to hold the wires in place.
http://www.ssnakess.com/photopost/data/500/1149rack-build9.jpg
Note: in this picture, the retainer clip has not yet been installed
Finishing
Next, hold in position and mount the 1/8 hardboard for the backing, again pay attention that you dont puncture the heat tape.
http://www.ssnakess.com/photopost/data/500/1149rack-build10.jpg
At this stage, you can finish all edge trimming and install all the screw head covers
Next drill a small hole through the hard board to allow passage of the probe for the thermometer. I placed my probe directly on the heat tape and secured with a piece of duct tape on the third shelf. If you wish, secure the mounting plate for the thermometer in a place of your choosing.
Next, silicone the slide thermostat onto the unit, again at a place of your choice.
Allow everything to dry thoroughly before use.
Plug it in and test it.
I also checked all nail heads holding the back in place to make sure that I had not punctured the heat tape. If you did you will get a shock. Remove the nail if this problem is discovered. I did end up with one that needed to be removed.
Well thats it. Put it into position, plug it in, set the temps and you are ready to go.
I let mine sit for a day, so that the temps could stabilize and then I prepped the containers. Drill air holes in the locations of your choice in the containers and make sure the holes arent too big for the snake to escape. Clean them and set them up with nothing more then a good bed of aspen and a water dish.
You do not need to put in hides if the snake is older, but for juveniles you can keep it simple and throw in a few toilet paper tubes and plastic containers for their added security.
This design allows for a very good heat and light gradient. Its easy to clean, easy to move around, takes up little space and is very strong.
Currently I am using this setup for juvenile corns, mid size kings, a juvenile boa, and 4 male ball python.
Here is a summary of costs:
All prices in Canadian Funds
5/8 Melamine 23.00
1/8 Hardboard 12.00
3 11 Heat tape 15.00
1 two prong extension cord - 6+ (cut off the female plug) 8.00
digitial dual probe thermometer 22.00
slide thermostat 20.00
6 Sterilite Model # 1856 container Available at Walmart 5.43 ea 32.58
solder for making connections between extension cord and heat tape or heat tape connectors
tube of silicone (clear or white) I used clear. 6.00
box of 100 - 1-1/2 Particleboard screws 5.00
screw head covers 3.00
melamine iron-on edge stripping (13/16x50) 8.00
small package 1 nails 1.00
duct tape 4.00
2 small brackets 1.00
Plus about 4 hours labour to assemble
Total: 160.00 or approx. 26.66 per snake housing
You will save more if you cut enough wood for two units
Plus tax of course. Your heat tape may be more, I did get a deal on mine through a private sale
UPDATE:
Initially, the recommendation was to mount the thermometer probe directly to the heat tape. Although this gives you an accurate reading at the source, it does not properly measure the temp inside the tubs. Since then, I have installed the probe inside the tub and put a sheet of double sided aluminum foil insulation across the back of the unit. Using the foil insulation greatly improves the efficiency in getting the heat back into the tub, where it is needed.
Well I hope this helps someone out, and if you have any further questions, drop me a line. Ill be happy to help.
Cheers
Jim